74 thoughts on “Forum

  • January 17, 2012 at 7:37 pm
    Permalink

    I have a “54” 3100. However the VIN # is H550005240.

    This plus a few other clues makes me think this is really a 55

    The “000” after the 55 is throwing me as (per my research) I should expect a letter to indicate the plant where it was built.

    Can anyone point me to somewhere else to look?

    Thanks

    Reply
    • January 17, 2012 at 7:59 pm
      Permalink

      You have a 1955 1st series. The truck is a 1/2 ton 3100 Series (H), a 55 1st series (55-almost identical to 1954), made in Fremont, CA (O) and was the 5,240 truck off the line (005240). Hope this helps and welcome to the site.

      Reply
      • May 8, 2012 at 6:55 pm
        Permalink

        OK, Great
        Thank You.

        Next question: for a 55 1st Series what is the “stock” original wheel size and tire size(s)
        Thanks, Doug

        Reply
        • April 17, 2020 at 12:09 am
          Permalink

          Has anyone installed under the dash clutch and brake pedals, on a 54 Chevy truck

          Reply
          • October 13, 2020 at 12:20 am
            Permalink

            Dennis, did you get the clutch / brake pedals installed under the dash? I have a 54 GMC and need to also install under the dash. I would appreciate any info as how you installed and what you installed.
            Thanks, Mike

    • June 15, 2019 at 7:17 pm
      Permalink

      What color were the stack bumpers on the 1950 Chevrolet pickup? The grille was body color and the backsplash bars were white?

      Reply
  • February 14, 2012 at 3:21 pm
    Permalink

    I have a GMC 100 1956 but i don´t know the boltpattern the only thing i know is that it´s 6 bolt, Can someone help me??

    Reply
  • March 10, 2012 at 6:23 pm
    Permalink

    I was thinking of paining the grill and bumpers black instead of the white. anyone have any thoughts on this?

    Reply
    • January 7, 2022 at 5:48 pm
      Permalink

      black sounds great. only person that has to like it is you. no matterwhat you do you’ll have ppl who like it and ppl who hate it. do what you like, experament and enjoy it. if you end up not liking it you have an excuse to get a new paint job,

      Reply
      • June 16, 2023 at 9:19 pm
        Permalink

        How do you prime a gas line to the engine from a gas tank behind the seat of a 56 Chevy pick up. It needs suction and I can’t figure out how to create such suction. I even bought a 200 ml suction syringe. It isn’t enough to draw the gas up from the tank. Any ideas?

        Reply
  • May 10, 2012 at 10:43 am
    Permalink

    Recently my dad gavemy son a 1953 5 window pu that is in need or restoration. Would it be better to keep original or customize it as far as value goes. It has the original engine and all original body.

    Reply
    • August 22, 2013 at 1:53 pm
      Permalink

      If you want your son to be able to drive it, make it a resto-mod. The value is up to you, with the sky the limit. But more importantly, it will be an enjoyable, usable truck, that is much safer and more comfortable to drive. My ’51 has a Chevy V8 engine and Turbo 350 transmission, which you can pick up on Craigslist for almost nothing. The front suspension and steering (front clip) is from a Camaro. It has vintage air. The engine came from a 1980 Chevy C10, so it included power steering. The truck now has power steering, power disc brakes, 3-point seat belts, A/C and modern heat, tilt-steering, and more modern gauges and stereo. It is dependable, gets pretty good gas mileage, drives like my Acura, and everyone that sees it loves it. Yet I don’t have much money in it – though a lot of hours. At the moment we are continuing to do upgrades, like padding the dash for improved looks and safety, and replacing the side windows with safety glass (the others have already been replaced), and updating the interior layout.

      Reply
      • March 31, 2016 at 7:42 pm
        Permalink

        Did you have to modify the cab floor for clearance for automatic transmission?

        Reply
        • May 17, 2016 at 7:23 am
          Permalink

          Not at all. Went in with no issues.

          Reply
          • October 23, 2016 at 8:24 pm
            Permalink

            Your article was exclelent and erudite.

  • May 27, 2012 at 4:48 pm
    Permalink

    I am looking at a 51 gmc where can I find ser.# and what would be a good starting price for a restorable truck. it was a driver then stored for 10 years

    Reply
    • July 26, 2020 at 7:32 pm
      Permalink

      Just picked up a 1952 2 Ton I believe.

      Information is hard to confirm from the serial number. Do you know of a good website for confirming the model, engine, etc of of the serial #

      Thank you

      Reply
  • August 27, 2012 at 5:39 pm
    Permalink

    I have found a 1957 GMC 1/2 ton for sale with a 347 Pontiac with tri power and a munci trans in it. the seller claims it is original and it it appears as it could be. Is this possible

    Reply
    • July 17, 2016 at 5:38 pm
      Permalink

      Yes ,I also have a 1957 GMC with the 347- This year and 1958 they were using Pontiac motors as a test for v8’s in pickups,after this they made a engine(V8) just for pickups

      Reply
      • December 21, 2016 at 6:32 pm
        Permalink

        I’m putting a pontiac 400 in my 55 old series the block is a 75 . What kind of motor mount is used on a 57 truck . Thanks for any info

        Reply
        • June 4, 2017 at 7:52 pm
          Permalink

          I have a 68 400 Pontiac in my series one 55 and love it

          Reply
  • October 1, 2012 at 10:58 am
    Permalink

    Does anyone know what a 1950 Chevy 1 1/2 ton truck with grain bed with a lift on it would be worth. It was bought new in 1950 and owned by the same people since. It is still a six volt system with the starter and gear shift on the floor. Still have the stock rack for it too.

    Reply
  • December 14, 2012 at 9:36 pm
    Permalink

    I what disc brakes and power steering on a 63 c20.most kits are 5 lug. Is ther a kit for 8 lug or will I be changing my rear-end also?

    Reply
  • February 25, 2013 at 11:57 pm
    Permalink

    i have a 1958 apache 3600 with a 9ft 3 inch step side bed ,not stretched or altered ,frame is one piece,wheel base is 133 inches.anyone have hany info on this?

    Reply
  • October 27, 2013 at 4:32 pm
    Permalink

    Does anyone know if a 1957 3100 and 3600 body and suspension parts would interchange?

    Reply
    • November 4, 2018 at 8:23 pm
      Permalink

      Just picked up a 57 3600 4×4 long bed. Claimed to be original chassis. Though, front end seems to be newer. Frame has been modified, including suspension parts. I can’t figure it out. In desperate need of some guidance. If your truck is stock, please send me pictures

      Reply
  • November 23, 2013 at 6:32 am
    Permalink

    Hi, I just wanted to say hi. I read this forum for quite some time and finally I registered.

    PS. Sorry for my English is not perfect yet …

    Reply
  • December 31, 2013 at 9:44 am
    Permalink

    I am doing small details on a ’57. Does anyone know the locations to install the three different bumpers on each door/door jamb. There are more holes than bumpers on each side so not sure of the placement of the 3 per side.

    Reply
  • February 18, 2014 at 5:59 pm
    Permalink

    We have a 1966 Chevy Cruise Air van. We know it was made off-site from Chevy. It is a fiberglass small rv. We cannot find any information on it. Can anyone help?

    Reply
  • August 2, 2014 at 2:47 pm
    Permalink

    Anyone know where I can locate a 1939/46 — 1/2 to 1 ton truck with a glass carrying body that can be restored and donated to a WWII museum?
    Pls respond to:
    Thanks,
    Howard

    Reply
    • April 28, 2019 at 5:19 am
      Permalink

      Yes , email me if interested 1941 1 1/2 ton panel longbed dually.needs resto, is completey together with resto parts, 1 of ywo known to exist. It is a chevy panel that was militarized then painted over with civilian colors.
      Call stu, 2672989399 or
      Stuartkentzumpfe@gmail.com

      Reply
  • August 24, 2014 at 8:55 pm
    Permalink

    I just purchased a 1959 Chevy Apache. How can I find out what model it is?

    Reply
  • September 8, 2014 at 12:03 pm
    Permalink

    I just bought an old Chevy pickup truck and I’m trying to figure out what year / model it is. The owner thought it was a ’41, but has no title and we can’t find the VIN. It is a wrecker and I found a wrecker permit that states its a 1944, which doesn’t seem possible due to the war. It has the 2 speed dually rear end with the 8.25×20 tires which narrows it down to the 5000 / 6000 series. But, the wheel base is 172″ which doesn’t seem to exist and it has “General Motors Truck” stamped into the passenger side of the hood. The motor ID starts with FEA, which a few sites think that is a ’48, but the grill doesn’t match. My grill has both the upper & lower slats oriented horizontally. Any ideas?

    Reply
  • March 28, 2015 at 7:48 pm
    Permalink

    I am looking for an old truck with or without a glass carrying body that can be restored and donated to a non-profit WWII Museum located at the site of the largest port of embarkation in the USA.

    Over a million and a half US shipped out from this camp, many of whom did not return. My four generation family operated a glass and metal business that helped build several US military bases and a display of the equipment used to construct the bases would be of interest to the school children and the “greatest generation” that that helped build them. Many thanks.

    Reply
  • April 5, 2015 at 3:39 pm
    Permalink

    I have recently bought a 1973 Chevy Cheyenne 1/2 ton. It is stock except for the engine. The engine is a 305 with 4 bbl from a 1984 Monte Carlo SS (according to the engine ID on the front passenger side plate of the engine). It currently has a Holley carb on it but can’t get it to work right. I need to know what carb needs to be on the engine for street usage. The engine otherwise is stock with a GM intake manifold, split plenum.

    Reply
    • April 5, 2015 at 3:46 pm
      Permalink

      Forgot to add that the present Holley is a manual chock carb, so would like to stay with a manual choke carb.

      Reply
  • June 16, 2015 at 12:15 pm
    Permalink

    I need parts to rebuild a manual column shifter and don’t know where to get them. I don’t want to put in a floor shifter. Any help is appreciated.

    Reply
  • July 31, 2015 at 3:38 pm
    Permalink

    Does anyone know the bolt pattern for a 1952 or 1953 3100? And what are the stock tire sizes front and rear for those years?

    Reply
  • September 26, 2015 at 11:37 pm
    Permalink

    Does anyone know a good source for some 1936 low cab chevy doors?
    Thx..

    Reply
  • October 6, 2015 at 7:58 pm
    Permalink

    I am rebuilding the front suspension of my 1966 C-10. I am needing a pair of offset upper control arm shafts so I can adjust the camber. Does anyone know where I can find these? I have searched the internet with no luck! Any info will be greatly appreciated!!!
    Thanks!

    Reply
  • December 20, 2015 at 11:01 pm
    Permalink

    I have a 72′ chevy blazer, 350, 4wd. I am needing to replace the fuel pump as well as a fuel line that connects the carb to th e fuel pump. I think I found the correct fuel line for that model but it’s listed for 2wd on the site I found it on. Is the fuel line that connects carb to fuel pump the same as for 2wd and 4wd on a 72′ blazer?

    Reply
  • March 6, 2016 at 6:06 am
    Permalink

    I’m getting my mother in laws 1960 Apache 10 up and running. When they parked it, the 350 they put in made it overheat. Would a newer, bigger radiator fix this issue?

    Reply
  • March 19, 2016 at 2:58 pm
    Permalink

    Hiya very niice web site!! Maan .. Beautiful ..
    Amazing .. I’ll bookmark your website and take the feeds also…I’m happy to find so may
    useful info right here within the put up, we’d like work
    outt more strategies on this regard, thank you for sharing.

    Reply
    • October 23, 2016 at 9:18 pm
      Permalink

      Haha, you are usually in mine too. We have a lot in common such as our feminist and religious (or lack of) views. I think a road trip may be in order one of these dasy0&#16!;

      Reply
  • April 23, 2016 at 12:00 am
    Permalink

    Have two 1 and 1/2 ton chevy trucks. ’47 and ’49. Both complete. Want to deal them

    Reply
  • July 10, 2016 at 4:25 pm
    Permalink

    Does anyone know if you can flat tow a 1952 Chevy pickup. Manual transmission..
    Flat 6…????

    Reply
  • August 31, 2016 at 3:32 pm
    Permalink

    i have a 1987 Chevy pickup with a 305 engine. the service engine light comes on after about 10- 15 minutes of driving.
    i changed the oxygen sensor and reset the code, however the light still comes on. any thoughts….

    Reply
  • September 7, 2016 at 7:09 am
    Permalink

    I very recently bought a 1953 truck. Unfortunately I didn’t realize it had a 54 bed. There’s not a huge difference, but I’m noticing that the cab appears to have a bit of a tilt. The cab corners appear to be lower giving the appearance that the doors are running down hill a bit. The gab between the cab corner and the bed is zero. The frame appears to be straight, but I’m afraid that something is terribly wrong with the way this cab mounts and I’m not sure how to address it. What should I look for concerning the way this cab mounts. I plan to take it to a shop and have them examine it more closely. Any advice would be helpful. I’m beginning to feel as though I took a bite out of a bad apple on this one.

    Reply
  • December 1, 2016 at 3:20 pm
    Permalink

    I have a low cab 1936 chevy truck that has the spare tire mounted on the driver’s side fender. All pictures I see of other ’36’s the spare is mounted on the Passenger side fender. So was there an option on this?

    Reply
  • December 24, 2016 at 11:08 am
    Permalink

    I have a 1974 camper special 2500 that has Chevrolet on the tailgate and a bowtie emblem in the grill. Title indicated chevy but it has a gmc emblem on the driver’s side behind the door on the cab molding. Any ideas? Thanks

    Reply
  • January 2, 2017 at 9:07 pm
    Permalink

    Hi may be interested in redoing a truck like my grandpa used to drive in our business. He started the business in 1904 and passed it on down to me. I think it is a 40s chevy if someone could look at it and tell me there is just a shot from the side. It is on mauller.com thanks

    Reply
  • January 10, 2017 at 11:29 am
    Permalink

    i’m trying to ID the engine in my recently purchased 1951 CHEVY 3100. IT’S A 6 CYL. with a 1 bbl Rochester carb. Truck has a 4 speed tranny.
    Here is set numbers found on the Head, near the spark plugs, on pass side: B35918241570
    there is also another # on the Block in front of the Starter: OII379IF55X

    I’ve tried the various cross references online but can’t come close.

    Reply
  • May 2, 2017 at 10:06 am
    Permalink

    Looking for a set of 5 vintage Jackman-style wheels. 8-spoke wagon wheels steel or aluminum. 15X8.5″ 6X5.5″ lugs. Please email me if you have a decent set you’d sell. Thx.

    Reply
  • October 14, 2017 at 11:46 am
    Permalink

    I have complete 1950 rear from a 3600 drum to drum with 4 rims and tires. Does anybody want them?

    Reply
  • December 15, 2017 at 10:07 pm
    Permalink

    I need to know what a 60-63 chevy truck double hump dash width is

    Reply
  • March 12, 2019 at 2:22 pm
    Permalink

    I have a 58 Apache I got spark fuel and compression but wont start any ideas

    Reply
  • March 14, 2019 at 6:43 pm
    Permalink

    I`ve got a 1955 2nd series, putting a 396 in it. running into a problem with radiator clearance. Any suggestions? I wanna run electric fans.

    Reply
  • August 25, 2019 at 1:05 pm
    Permalink

    I am restoring a 59 Apache 2500 long bed step side. The bought some original 59 steps to replace mine. However, they are longer than what was on my truck. Were there different sized steps made for the 58-59 models of Apaches?

    My originals on the truck were 32 1/2″ at the longest run and 25″ at the shortest run were it angle up.
    Purchased originals were 36 1/2″ and 30 3/8″ respectively.

    Any help is appreciated.

    Reply
  • September 15, 2019 at 4:11 pm
    Permalink

    I have a 1955 Chevy 3100 that is in need of a complete seat recovering, it is down to the springs. Is there a kit I can buy to reupholster the seat myself?

    Reply
  • December 29, 2019 at 5:30 pm
    Permalink

    I have a picture of me as a very small child standing in front of our truck at the time. The only thing I can identify on it is “GMC 100” on the driver’s side. I would love to know what year it is. Based on pictures found on the internet, it could be a ‘49 or ‘50 but I’m not sure. I’m happy to share the picture. Any ideas?

    Reply
    • January 7, 2020 at 12:08 am
      Permalink

      Yes please share pic!

      Reply
  • January 9, 2020 at 5:55 pm
    Permalink

    I’m looking for a wind shield wiper (motor, arm, blade, wiring, the entire works or and part there of) for a 1945/1946 Chevy pick up

    Reply
  • November 18, 2020 at 11:48 pm
    Permalink

    Anyone know how to convert a glove box cover to open slowly with a touch? I seen something similar on the ICON thriftmaster truck dash panel. I have a 49 3100 chevy truck .
    Thanks, Terry

    Reply
  • December 15, 2020 at 5:11 am
    Permalink

    I have a 1954 chevy 6500 I am restoring and could use some help. First step for me is disc brakes, I am struggling to find kits. The dually rear end is 10 lug, the front is 5. As I plant to have her loaded with four cord of wood on the regular I want good working brakes right away. Any advice help appreciated

    Bo

    Reply
  • November 8, 2021 at 12:41 am
    Permalink

    Just purchased a 42 Chevy Master 1/2 ton Pickup.
    Fantastic condition. No rust, no dents or ding’s.
    Tires (6.50-16LT) are cracking, dry rotting. Wondering what Modern Radial size to replace with.
    Appreciate replies.

    Reply
  • July 15, 2022 at 6:06 am
    Permalink

    I am assisting in setting up a new museum for antique and classic cars near my city, Mysore, South India.

    One of the light trucks on display is supposedly a 1926 Chevrolet as badged by its owner, but lacks any form of identification in terms of logos or manufacturer’s plate.

    The engine is a 4-cylinder, side-valve unit, so I am inclined to think it may be a Ford.

    I would like to send photographs of the vehicle and engine bay with a request to correctly identify this vehicle. Please send me an email address where these photos could be sent.

    Thank you.

    Reply
  • October 30, 2022 at 12:47 am
    Permalink

    Per the serial number my Chevy 3100 is a 1952 but when I looked at the engines serial number it shows it’s a 1953. My guess is that the engine was replaced but is it possible that the truck was manufactured late enough in the year to get a 1953 engine. Per the serial number the truck was manufactured in September. I appreciate any feedback.

    Reply
  • December 1, 2022 at 1:19 am
    Permalink

    need info on the interchange of cab from any c 10 to fit my 77 c 10 pick up thanks

    Reply
  • January 19, 2023 at 9:34 pm
    Permalink

    Is a 1957 Chevrolet 3100 short bed step side a Passport or a Apache??? I was told 1958 was the first Apache.

    Reply
    • January 19, 2023 at 9:48 pm
      Permalink

      Never heard the name Passport, but Apache naming didn’t start until 1958 like you were told.

      Reply
  • January 3, 2024 at 6:12 pm
    Permalink

    The kickdown mechanism for passing gear was stolen from my carb many years ago. Does anyone make a replacement? 1969 C20 350 engine with stock automatic and an electronic solenoid for passing gear engagement.

    Reply
  • January 4, 2024 at 10:29 pm
    Permalink

    I brought a 53 Chevy custom frame from Scott’s Hotrod and I am looking for mounting ideas for back of cab. Very different
    Thanks B-Rad

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *